Orifice
Properties
| AdjustVarType |
If an Adjust object is attached to this object, returns a variable describing how this object is used by it (manipulated, controlled or reference).
(Inherited from BaseClass) |
| Annotation | (Inherited from BaseClass) |
| AttachedAdjustId |
If an Adjust object is attached to this object, returns its ID.
(Inherited from BaseClass) |
| AttachedInfoCarrierId | (Inherited from BaseClass) |
| AttachedSpecId |
If an Specification object is attached to this object, returns its ID.
(Inherited from BaseClass) |
| AttachedUtilities | (Inherited from BaseClass) |
| Beta | Gets or sets the diameter ratio β = d/D (orifice diameter / pipe internal diameter). |
| Bottom | (Inherited from BaseClass) |
| Calculated | (Inherited from BaseClass) |
| CalculationMethod | Gets or sets the two-phase flow calculation method used when both phases are present. |
| CanUsePreviousResults | (Inherited from BaseClass) |
| ComponentDescription |
Gets or sets the CAPE-OPEN component description for this unit operation.
(Inherited from UnitOpBaseClass) |
| ComponentName |
Gets or sets the CAPE-OPEN component name for this unit operation.
(Inherited from UnitOpBaseClass) |
| CorrectionFactor | Gets or sets a dimensionless correction factor applied to the calculated discharge coefficient. |
| CreateChartAction | (Inherited from BaseClass) |
| DebugMode | (Inherited from BaseClass) |
| DebugText | (Inherited from BaseClass) |
| DeltaT | Gets or sets the calculated temperature change (K) across the orifice plate. |
| DetailedDebugReport | (Inherited from BaseClass) |
| Dimensions |
Gets or sets the list of physical dimensions (e.g. vessel diameter, length) associated with this unit operation.
(Inherited from UnitOpBaseClass) |
| DynamicsOnly | (Inherited from BaseClass) |
| DynamicsSpec | (Inherited from BaseClass) |
| EnergyFlow |
Energy Flow property. Only implemented for Energy Streams.
(Inherited from BaseClass) |
| EquipmentTypes |
Gets the list of available equipment type names supported by this unit operation.
(Inherited from UnitOpBaseClass) |
| ErrorMessage |
Gets or sets the error message regarding the last calculation attempt.
(Inherited from BaseClass) |
| ExternalSolverConfigData |
Gets or sets serialized configuration data for the external solver associated with this unit operation.
(Inherited from UnitOpBaseClass) |
| ExternalSolverID |
Gets or sets the unique identifier of an external solver to be used for this unit operation.
(Inherited from UnitOpBaseClass) |
| ExtraProperties | (Inherited from BaseClass) |
| ExtraPropertiesDescriptions | (Inherited from BaseClass) |
| ExtraPropertiesTypes | (Inherited from BaseClass) |
| ExtraPropertiesUnitTypes | (Inherited from BaseClass) |
| FlowSheet |
Gets the current flowsheet where this object is located.
(Inherited from BaseClass) |
| GHGEmissionData | (Inherited from BaseClass) |
| GraphicObject |
Gets or sets the graphic object representation of this object in the flowsheet.
(Inherited from BaseClass) |
| HasPropertiesForDynamicMode | Gets a value indicating whether this unit operation exposes dedicated properties for dynamic mode. (Overrides BaseClassHasPropertiesForDynamicMode) |
| Height | (Inherited from BaseClass) |
| InfoCarrierVarType | (Inherited from BaseClass) |
| InternalPipeDiameter | Gets or sets the internal pipe bore diameter (m) upstream of the orifice. |
| IsAdjustAttached |
Checks if an Adjust operation is attached to this object.
(Inherited from BaseClass) |
| IsDirty | (Inherited from BaseClass) |
| IsFunctional | (Inherited from BaseClass) |
| IsInfoCarrierAttached | (Inherited from BaseClass) |
| IsSink | (Inherited from BaseClass) |
| IsSource | (Inherited from BaseClass) |
| IsSpecAttached |
Checks if an Specification operation is attached to this object.
(Inherited from BaseClass) |
| LastSolutionInputSnapshot | (Inherited from BaseClass) |
| LastUpdated | (Inherited from BaseClass) |
| Left | (Inherited from BaseClass) |
| MobileCompatible | Gets a value indicating whether this unit operation is compatible with mobile interfaces. (Overrides BaseClassMobileCompatible) |
| Name |
Object's Unique ID (Name)
(Inherited from BaseClass) |
| ObjectClass | Gets or sets the simulation object class category for this orifice plate (PressureChangers). (Overrides BaseClassObjectClass) |
| OrificeDiameter | Gets or sets the orifice bore diameter (m). |
| OrificePressureDrop | Gets or sets the differential pressure (Pa) measured directly across the orifice throat. |
| OrifType | Gets or sets the pressure tap configuration of this orifice plate. |
| OverallPressureDrop | Gets or sets the total pressure drop (Pa) across the orifice plate including flow recovery losses. |
| OverrideCalculationRoutine | (Inherited from BaseClass) |
| ParticleSizeDistributions |
Gets or sets the dictionary of particle size distribution data, keyed by compound or stream name.
(Inherited from UnitOpBaseClass) |
| Phases |
Phase collection, only implemented for Material Streams.
(Inherited from BaseClass) |
| PreferredFlashAlgorithmTag | (Inherited from BaseClass) |
| ProductAssembly | (Inherited from BaseClass) |
| ProductAuthor | (Inherited from BaseClass) |
| ProductContactInfo | (Inherited from BaseClass) |
| ProductDescription | (Inherited from BaseClass) |
| ProductName | (Inherited from BaseClass) |
| ProductPage | (Inherited from BaseClass) |
| ProductVersion | (Inherited from BaseClass) |
| PropertyPackage |
Gets or sets the property package associated with this object.
(Inherited from UnitOpBaseClass) |
| Right | (Inherited from BaseClass) |
| SelectedEquipmentType |
Gets or sets the name of the equipment type currently selected for this unit operation.
(Inherited from UnitOpBaseClass) |
| SpecVarType |
If an Specification object is attached to this object, returns a variable describing how this object is used by it (target or source).
(Inherited from BaseClass) |
| StoreDetailedDebugReport | (Inherited from BaseClass) |
| SupportsDynamicMode | Gets a value indicating whether this unit operation supports dynamic simulation mode. (Overrides BaseClassSupportsDynamicMode) |
| SupportsParticleSizeDistributions |
Gets a value indicating whether this unit operation supports particle size distribution calculations.
(Inherited from UnitOpBaseClass) |
| SupportsRestoreStateAfterError |
Gets a value indicating whether this unit operation supports restoring its state after a solver error.
(Inherited from UnitOpBaseClass) |
| Top | (Inherited from BaseClass) |
| UserDefinedChartNames | (Inherited from BaseClass) |
| Visible | (Inherited from BaseClass) |
| Width | (Inherited from BaseClass) |