Difference between revisions of "Capital Cost Estimator"

From DWSIM - Open Source Chemical Process Simulator
Jump to navigation Jump to search
(Created page with "About Capital Cost Estimator is a software which estimates Capital and Operating Costs for a Chemical Processing Plant based on data from the currently active flowsheet. WARN...")
 
Line 1: Line 1:
About
+
= About =
 
Capital Cost Estimator is a software which estimates Capital and Operating Costs for a Chemical Processing Plant based on data from the currently active flowsheet.
 
Capital Cost Estimator is a software which estimates Capital and Operating Costs for a Chemical Processing Plant based on data from the currently active flowsheet.
  
WARNING
+
= WARNING =
  
 
This software should be used for educational purposes only!
 
This software should be used for educational purposes only!
Line 8: Line 8:
 
The data and information within the software has been obtained from a wide variety of literature sources. While reasonable care has been exercised in the collection of data and testing of this software, the author of the software disclaims any warranty, expressed or implied, as to the accuracy or reliability of the data or calculations contained therein. The results of calculations obtained from the software yield approximate results, which will not always be suitable for every application. The software is designed for use by trained professional personnel and is not a substitute for sound professional judgment. It is the sole responsibility of the user to validate the data presented by the software and to determine whether the results of this program are accurate and suitable for any specific purpose. No guarantee of accuracy or fitness for any purpose is expressed or implied. The author strongly recommends that the data be checked against other sources and/or methods before use and application. The author shall not be held liable for any direct, indirect, consequential or incidental damages incurred through use of the data or calculations.
 
The data and information within the software has been obtained from a wide variety of literature sources. While reasonable care has been exercised in the collection of data and testing of this software, the author of the software disclaims any warranty, expressed or implied, as to the accuracy or reliability of the data or calculations contained therein. The results of calculations obtained from the software yield approximate results, which will not always be suitable for every application. The software is designed for use by trained professional personnel and is not a substitute for sound professional judgment. It is the sole responsibility of the user to validate the data presented by the software and to determine whether the results of this program are accurate and suitable for any specific purpose. No guarantee of accuracy or fitness for any purpose is expressed or implied. The author strongly recommends that the data be checked against other sources and/or methods before use and application. The author shall not be held liable for any direct, indirect, consequential or incidental damages incurred through use of the data or calculations.
  
Features
+
= Features =
Capital Cost Estimation
+
* Capital Cost Estimation
Yearly Operating Cost Estimation
+
* Yearly Operating Cost Estimation
Saving/Loading of Cost Reports
+
* Saving/Loading of Cost Reports
Compare multiple Cost Reports
+
* Compare multiple Cost Reports
Import Data from DWSIM Simulation Files, COCO/COFE Flowsheet files and DESIGN II Excel Reports (standalone version only)
+
* Import Data from DWSIM Simulation Files, COCO/COFE Flowsheet files and DESIGN II Excel Reports (standalone version only)
Export results to DOC/ODT/XLS/ODS/PDF files
+
* Export results to DOC/ODT/XLS/ODS/PDF files
Automatic mapping for selected equipments, product/raw streams and utilities
+
* Automatic mapping for selected equipments, product/raw streams and utilities
Price correction based on CEPCI and IPC Cost Indexes
+
* Price correction based on CEPCI and IPC Cost Indexes
Currency conversion
+
* Currency conversion
System Requirements
+
= System Requirements =
 
Supported Operating Systems: Windows/Linux
 
Supported Operating Systems: Windows/Linux
 
[DWSIM Plugin Version] Minimum required DWSIM version: 4.3 with Update 6
 
[DWSIM Plugin Version] Minimum required DWSIM version: 4.3 with Update 6
 
[Standalone Application Version] Minimum required Framework version: .NET 4.5/Mono 4.0
 
[Standalone Application Version] Minimum required Framework version: .NET 4.5/Mono 4.0
Download
+
= Download =
Plugin for DWSIM Simulator
+
== Plugin for DWSIM Simulator ==
 
The Capital Cost Estimator Plugin for DWSIM Simulator is available to purchase for USD 25. The software license is non-transferrable, that is, after downloading the plugin, you cannot redistribute it to anyone.
 
The Capital Cost Estimator Plugin for DWSIM Simulator is available to purchase for USD 25. The software license is non-transferrable, that is, after downloading the plugin, you cannot redistribute it to anyone.
  
 
A lot of effort was put on making this software, in the hope that it will be useful. You can support future developments simply by doing things the right way: please do not give this plugin for free to anyone, and encourage your colleagues to download it through the official channel.
 
A lot of effort was put on making this software, in the hope that it will be useful. You can support future developments simply by doing things the right way: please do not give this plugin for free to anyone, and encourage your colleagues to download it through the official channel.
  
Click here to go to the download/purchase page: Capital Cost Estimator (DWSIM Plugin Version) Download Page
+
Click here to go to the download/purchase page: [https://gum.co/UkBaq Capital Cost Estimator (DWSIM Plugin Version) Download Page]
  
A demo version which doesn't allow saving, loading and/or exporting the results is available to download from here.
+
== Standalone Application ==
 
 
Standalone Application
 
 
The Capital Cost Estimator (Standalone App Version) is available to purchase for USD 29. The software license is non-transferrable, that is, after downloading the package, you cannot redistribute it to anyone.
 
The Capital Cost Estimator (Standalone App Version) is available to purchase for USD 29. The software license is non-transferrable, that is, after downloading the package, you cannot redistribute it to anyone.
  
Click here to go to the download/purchase page: Capital Cost Estimator (Standalone App Version) Download Page
+
Click here to go to the download/purchase page: [https://gumroad.com/products/EEpHG/edit Capital Cost Estimator (Standalone App Version) Download Page]
 
 
A demo version which doesn't allow saving, loading and/or exporting the results is available to download from here.
 
  
Installation
+
= Installation =
DWSIM Plugin Version
+
== DWSIM Plugin Version ==
 
Unzip the downloaded package. Copy the DWSIM.CapitalCostEstimator.dll and DWSIM.CapitalCostEstimator.pdb files to the "plugins" folder inside DWSIM's current installation directory.
 
Unzip the downloaded package. Copy the DWSIM.CapitalCostEstimator.dll and DWSIM.CapitalCostEstimator.pdb files to the "plugins" folder inside DWSIM's current installation directory.
  
Running the plugin
+
=== Running the plugin ===
 
Start DWSIM and open/create a flowsheet. Go to the "Plugins" menu, you should see a new item called "Capital Cost Estimator". Click on it and the plugin interface will be shown on the screen.
 
Start DWSIM and open/create a flowsheet. Go to the "Plugins" menu, you should see a new item called "Capital Cost Estimator". Click on it and the plugin interface will be shown on the screen.
  
 
Existing Unit Operations and Material/Energy Streams will be mapped to Equipments, Materials and Utilities, whose parameters can be freely modified.
 
Existing Unit Operations and Material/Energy Streams will be mapped to Equipments, Materials and Utilities, whose parameters can be freely modified.
  
Standalone Application Version
+
== Standalone Application Version ==
 
Unzip the downloaded package and run the executable file.
 
Unzip the downloaded package and run the executable file.
  
General Usage Instructions
+
= General Usage Instructions =
New/Load/Save
+
== New/Load/Save ==
 
To create a new Cost Report, click on the "New Report" menu button.
 
To create a new Cost Report, click on the "New Report" menu button.
 
To load an existing report, click on the "Load Report" menu button.
 
To load an existing report, click on the "Load Report" menu button.
 
To save the currently selected report, click on the "Save Report" menu button.
 
To save the currently selected report, click on the "Save Report" menu button.
Compare Reports
+
== Compare Reports ==
 
To compare the currently opened reports, click on the "Compare Reports" menu button.
 
To compare the currently opened reports, click on the "Compare Reports" menu button.
  
Report Setup
+
== Report Setup ==
 
On this tab you will enter basic report information like name, description, reference date, cost index selection and currency details. The currency converter is based on a webservice, which depends on an active internet connection to work.
 
On this tab you will enter basic report information like name, description, reference date, cost index selection and currency details. The currency converter is based on a webservice, which depends on an active internet connection to work.
  
Ccostplugin1.png
+
[[File:Ccostplugin1.png]]
  
Equipment Mapping
+
== Equipment Mapping ==
 
Some equipments are automatically mapped from Unit Operations, though you can modify the calculated values and change the selected equipments at any time. The correction factors are multiplied by the current prices to form the final total equipment cost.
 
Some equipments are automatically mapped from Unit Operations, though you can modify the calculated values and change the selected equipments at any time. The correction factors are multiplied by the current prices to form the final total equipment cost.
  
Ccostplugin2.png
+
[[File:Ccostplugin2.png]]
  
Material Stream Mapping
+
== Material Stream Mapping ==
 
Material Streams can be mapped to Raw Materials and/or Products, which will be used to calculate Yearly Operating Costs.
 
Material Streams can be mapped to Raw Materials and/or Products, which will be used to calculate Yearly Operating Costs.
  
Ccostplugin4.png
+
[[File:Ccostplugin4.png]]
  
Utility Mapping
+
== Utility Mapping ==
 
You can map Material and Energy Streams to some predefined Process Utilities, and the plugin will automatically calculate the cost based on the mass or energy flow, depending on the stream type.
 
You can map Material and Energy Streams to some predefined Process Utilities, and the plugin will automatically calculate the cost based on the mass or energy flow, depending on the stream type.
  
Ccostplugin5.png
+
[[File:Ccostplugin5.png]]
  
Capital Cost Summary
+
== Capital Cost Summary ==
 
Here you'll see a summary of the items that make up the Total Capital Cost. You can change the calculation basis (Percentage or Absolute value) for most items, except for those who are calculated based on the previously mapped items.
 
Here you'll see a summary of the items that make up the Total Capital Cost. You can change the calculation basis (Percentage or Absolute value) for most items, except for those who are calculated based on the previously mapped items.
  
Ccostplugin6.png
+
[[File:Ccostplugin6.png]]
  
Yearly Operating Cost Summary
+
== Yearly Operating Cost Summary ==
 
Here you'll see a summary of the items that make up the Total Yearly Operating Cost. You can change the calculation basis (Percentage or Absolute value) for most items, except for those who are calculated based on the previously mapped items.
 
Here you'll see a summary of the items that make up the Total Yearly Operating Cost. You can change the calculation basis (Percentage or Absolute value) for most items, except for those who are calculated based on the previously mapped items.
  
Ccostplugin7.png
+
[[File:Ccostplugin7.png]]
  
Export Results
+
== Export Results ==
 
From this tab you can export the calculated results to a document file (DOC, ODT, PDF) or a spreadsheet file (XLS, ODS).
 
From this tab you can export the calculated results to a document file (DOC, ODT, PDF) or a spreadsheet file (XLS, ODS).
  
Ccostplugin8.png
+
[[File:Ccostplugin8.png]]
  
Cost Estimation Basis
+
= Cost Estimation Basis =
 
Most of the calculation methods on this plugin are based on the Factorial Method described on the Chemical Engineering Design book by R. K. Sinott [1], which you should refer to for more information.
 
Most of the calculation methods on this plugin are based on the Factorial Method described on the Chemical Engineering Design book by R. K. Sinott [1], which you should refer to for more information.
  
Introduction
+
== Introduction==
 
Cost estimation is a specialised subject and a profession in its own right. The design engineer, however, needs to be able to make quick, rough, cost estimates to decide between alternative designs and for project evaluation. Chemical plants are built to make a profit, and an estimate of the investment required and the cost of production are needed before the profitability of a project can be assessed.
 
Cost estimation is a specialised subject and a profession in its own right. The design engineer, however, needs to be able to make quick, rough, cost estimates to decide between alternative designs and for project evaluation. Chemical plants are built to make a profit, and an estimate of the investment required and the cost of production are needed before the profitability of a project can be assessed.
  
Accuracy and Purpose of Capital Cost Estimates
+
==Accuracy and Purpose of Capital Cost Estimates==
 
The accuracy of an estimate depends on the amount of design detail available: the accuracy of the cost data available; and the time spent on preparing the estimate. In the early stages of a project only an approximate estimate will be required, and justified, by the amount of information by then developed.
 
The accuracy of an estimate depends on the amount of design detail available: the accuracy of the cost data available; and the time spent on preparing the estimate. In the early stages of a project only an approximate estimate will be required, and justified, by the amount of information by then developed.
  
 
Capital cost estimates can be broadly classified into three types according to their accuracy and purpose:
 
Capital cost estimates can be broadly classified into three types according to their accuracy and purpose:
  
Preliminary (approximate) estimates, accuracy typically 30 per cent, which are used in initial feasibility studies and to make coarse choices between design alternatives. They are based on limited cost data and design detail.
+
* Preliminary (approximate) estimates, accuracy typically 30 per cent, which are used in initial feasibility studies and to make coarse choices between design alternatives. They are based on limited cost data and design detail.
Authorisation (Budgeting) estimates, accuracy typically 10 15 per cent. These are used for the authorisation of funds to proceed with the design to the point where an accurate and more detailed estimate can be made. Authorisation may also include funds to cover cancellation charges on any long delivery equipment ordered at this stage of the design to avoid delay in the project. In a contracting organisation this type of estimate could be used with a large contingency factor to obtain a price for tendering. Normally, however, an accuracy of about š5 per cent would be needed and a more detailed estimate would be made, if time permitted. With experience, and where a company has cost data available from similar projects, estimates of acceptable accuracy can be made at the flow-sheet stage of the project. A rough P&I diagram and the approximate sizes of the major items of equipment would also be needed.
+
* Authorisation (Budgeting) estimates, accuracy typically 10 15 per cent. These are used for the authorisation of funds to proceed with the design to the point where an accurate and more detailed estimate can be made. Authorisation may also include funds to cover cancellation charges on any long delivery equipment ordered at this stage of the design to avoid delay in the project. In a contracting organisation this type of estimate could be used with a large contingency factor to obtain a price for tendering. Normally, however, an accuracy of about š5 per cent would be needed and a more detailed estimate would be made, if time permitted. With experience, and where a company has cost data available from similar projects, estimates of acceptable accuracy can be made at the flow-sheet stage of the project. A rough P&I diagram and the approximate sizes of the major items of equipment would also be needed.
Detailed (Quotation) estimates, accuracy 5-10 per cent, which are used for project cost control and estimates for fixed price contracts. These are based on the completed (or near complete) process design, firm quotations for equipment, and a detailed breakdown and estimation of the construction cost.
+
* Detailed (Quotation) estimates, accuracy 5-10 per cent, which are used for project cost control and estimates for fixed price contracts. These are based on the completed (or near complete) process design, firm quotations for equipment, and a detailed breakdown and estimation of the construction cost.
 
The cost of preparing an estimate increases from about 0.1 per cent of the total project cost for 30 per cent accuracy, to about 2 per cent for a detailed estimate with an accuracy of š5 per cent.
 
The cost of preparing an estimate increases from about 0.1 per cent of the total project cost for 30 per cent accuracy, to about 2 per cent for a detailed estimate with an accuracy of š5 per cent.
  
Cost Escalation (Inflation)
+
==Cost Escalation (Inflation)==
 
The cost of materials and labour has been subject to inflation since Elizabethan times. All cost-estimating methods use historical data, and are themselves forecasts of future costs. Some method has to be used to update old cost data for use in estimating at the design stage, and to forecast the future construction cost of the plant.
 
The cost of materials and labour has been subject to inflation since Elizabethan times. All cost-estimating methods use historical data, and are themselves forecasts of future costs. Some method has to be used to update old cost data for use in estimating at the design stage, and to forecast the future construction cost of the plant.
  
Line 119: Line 115:
 
A cost index is the ratio of the actual price in a time period compared to that in a selected base period (a defined point in time or the average price in a certain year), multiplied by 100. Raw materials, products and energy prices, labor and construction costs change at different rates, and plant construction cost indexes are actually a composite, able to compare generic chemical plants capital costs.
 
A cost index is the ratio of the actual price in a time period compared to that in a selected base period (a defined point in time or the average price in a certain year), multiplied by 100. Raw materials, products and energy prices, labor and construction costs change at different rates, and plant construction cost indexes are actually a composite, able to compare generic chemical plants capital costs.
  
Calculation methods
+
==Calculation methods==
 
Although the available indexes are compiled in several ways, they are defined to encompass a specific set of conditions and items. Prices for these items can be obtained either through company’s purchasing department data or through published indexes, like those published by the Bureau of Labor Statistics (BLS).[3] Both the CE and the IC indexes, from Chemical Engineering and Intratec, respectively, employs BLS’ data.
 
Although the available indexes are compiled in several ways, they are defined to encompass a specific set of conditions and items. Prices for these items can be obtained either through company’s purchasing department data or through published indexes, like those published by the Bureau of Labor Statistics (BLS).[3] Both the CE and the IC indexes, from Chemical Engineering and Intratec, respectively, employs BLS’ data.
  
 
The weighting of such factors, which is defined by the realized degree of importance of each component in the specific index (or sub-index), aims to represent the costs variations typically found for chemical plants.
 
The weighting of such factors, which is defined by the realized degree of importance of each component in the specific index (or sub-index), aims to represent the costs variations typically found for chemical plants.
  
Using a cost index
+
==Using a cost index==
 
To update an item cost (equipment, projects) from period A to period B, is necessary to multiply period A’s cost by the ratio of period B’s index over period A’s index, according to the following equation:
 
To update an item cost (equipment, projects) from period A to period B, is necessary to multiply period A’s cost by the ratio of period B’s index over period A’s index, according to the following equation:
  
Line 131: Line 127:
 
As a rule-of-thumb, cost indexes permit fairly accurate estimates for cost escalation if the difference between period A and period B is less than 10 years. Differences between the actual equipment and labor prices and those predicted by the index tend to grow over the years, surpassing the typical error verified in budget-level estimates.[4][5]
 
As a rule-of-thumb, cost indexes permit fairly accurate estimates for cost escalation if the difference between period A and period B is less than 10 years. Differences between the actual equipment and labor prices and those predicted by the index tend to grow over the years, surpassing the typical error verified in budget-level estimates.[4][5]
  
Cost Indexes in Engineering
+
==Cost Indexes in Engineering==
 
The selection of the proper index to use depends on the industry in which it is applied. For example, while CE, M&S or IC Index are typically employed for chemical process industries, the ENR (Engineering News-Record) construction index is used for general industrial construction and takes in account the prices for fixed amounts of structural steel, cement, lumber and labor.
 
The selection of the proper index to use depends on the industry in which it is applied. For example, while CE, M&S or IC Index are typically employed for chemical process industries, the ENR (Engineering News-Record) construction index is used for general industrial construction and takes in account the prices for fixed amounts of structural steel, cement, lumber and labor.
  
Line 138: Line 134:
 
The main indexes available for process industries include:
 
The main indexes available for process industries include:
  
Chemical Engineering Index, CEPCI: composed of 4 major components – equipment, construction labor, buildings, and engineering and supervision – the index is employed primary as a process plant construction index, was established using a base period of 1957-1959 as 100. The CE Index is updated monthly and it lags in time by about 3 months. The CE Index was revised in 1982, to account for changes in labor productivity and, again, in 2002.[6] Published in each issue of Chemical Engineering.[7][8]
+
* Chemical Engineering Index, CEPCI: composed of 4 major components – equipment, construction labor, buildings, and engineering and supervision – the index is employed primary as a process plant construction index, was established using a base period of 1957-1959 as 100. The CE Index is updated monthly and it lags in time by about 3 months. The CE Index was revised in 1982, to account for changes in labor productivity and, again, in 2002.[6] Published in each issue of Chemical Engineering.[7][8]
Marshall and Swift Cost Index, M&S (originally known as Marshall and Stevens Index): a composite of two major components - process-industry equipment average and all-industry equipment average - was established in 1926 with a value of 100. Some industries considered in the process-industry equipment average are chemicals, petroleum products, rubber and paper. The all-industry average encompasses 47 different types of industrial, commercial and housing equipment. Published monthly in each issue of Chemical Engineering until April 2012.[9]
+
* Marshall and Swift Cost Index, M&S (originally known as Marshall and Stevens Index): a composite of two major components - process-industry equipment average and all-industry equipment average - was established in 1926 with a value of 100. Some industries considered in the process-industry equipment average are chemicals, petroleum products, rubber and paper. The all-industry average encompasses 47 different types of industrial, commercial and housing equipment. Published monthly in each issue of Chemical Engineering until April 2012.[9]
 
Intratec Chemical Plant Construction Index, IPC: a process plant construction index developed by Intratec, a chemical consulting company. Although cost indexes do not usually forecast future escalation, the IC Index stands out for presenting a smaller delay between release date and index date, besides a 12 months forecast. On the other hand, the index is only available from January 2000 (with a value of 100). A sample is available at Intratec’s website.[10]
 
Intratec Chemical Plant Construction Index, IPC: a process plant construction index developed by Intratec, a chemical consulting company. Although cost indexes do not usually forecast future escalation, the IC Index stands out for presenting a smaller delay between release date and index date, besides a 12 months forecast. On the other hand, the index is only available from January 2000 (with a value of 100). A sample is available at Intratec’s website.[10]
Nelson-Farrar Indexes, NF (originally known as the Nelson Refinery Construction Indexes): established in 1946 with a value of 100, the index is more suitable for petroleum or petrochemical business. Published once a month in the Oil and Gas Journal.
+
* Nelson-Farrar Indexes, NF (originally known as the Nelson Refinery Construction Indexes): established in 1946 with a value of 100, the index is more suitable for petroleum or petrochemical business. Published once a month in the Oil and Gas Journal.
 
Location Factor
 
Location Factor
 
In order to be able to use the available standard indexes to locations where index data is not available we have to incorporate a new term called the Location Factor (LF) to the standard index value. It is a dimensionless value for a particular location relative to either of the above-mentioned basis:
 
In order to be able to use the available standard indexes to locations where index data is not available we have to incorporate a new term called the Location Factor (LF) to the standard index value. It is a dimensionless value for a particular location relative to either of the above-mentioned basis:
Line 151: Line 147:
 
Location factors are greatly influenced by currency exchange rates due to their significant effect on Index value and hence vary drastically with time. Over the past couple of decades the location factors for various locations are trending close to the value 1. However location factor for a particular region within a country can be easily determined by adding 10% to the index of the reference location for every 1000 miles. The reference location is usually a major industrial location closest to the location where the index is being determined. Location factors for various locations have been published and updated in various journals as in Aspen Richardson's "International Construction Cost Factor Location Manual (2003)".
 
Location factors are greatly influenced by currency exchange rates due to their significant effect on Index value and hence vary drastically with time. Over the past couple of decades the location factors for various locations are trending close to the value 1. However location factor for a particular region within a country can be easily determined by adding 10% to the index of the reference location for every 1000 miles. The reference location is usually a major industrial location closest to the location where the index is being determined. Location factors for various locations have been published and updated in various journals as in Aspen Richardson's "International Construction Cost Factor Location Manual (2003)".
  
The Factorial Method for Capital Cost Estimation
+
==The Factorial Method for Capital Cost Estimation==
 
Capital cost estimates for chemical process plants are often based on an estimate of the purchase cost of the major equipment items required for the process, the other costs being estimated as factors of the equipment cost. The accuracy of this type of estimate will depend on what stage the design has reached at the time the estimate is made, and on the reliability of the data available on equipment costs. In the later stages of the project design, when detailed equipment specifications are available and firm quotations have been obtained, an accurate estimation of the capital cost of the project can be made.
 
Capital cost estimates for chemical process plants are often based on an estimate of the purchase cost of the major equipment items required for the process, the other costs being estimated as factors of the equipment cost. The accuracy of this type of estimate will depend on what stage the design has reached at the time the estimate is made, and on the reliability of the data available on equipment costs. In the later stages of the project design, when detailed equipment specifications are available and firm quotations have been obtained, an accurate estimation of the capital cost of the project can be made.
  
Lang factors
+
==Lang factors==
 
The factorial method of cost estimation is often attributed to Lang (1948). The fixed capital cost of the project is given as a function of the total purchase equipment cost by the equation:
 
The factorial method of cost estimation is often attributed to Lang (1948). The fixed capital cost of the project is given as a function of the total purchase equipment cost by the equation:
  
Line 165: Line 161:
 
The above equation can be used to make a quick estimate of capital cost in the early stages of project design, when the preliminary flow-sheets have been drawn up and the main items of equipment roughly sized.
 
The above equation can be used to make a quick estimate of capital cost in the early stages of project design, when the preliminary flow-sheets have been drawn up and the main items of equipment roughly sized.
  
Detailed factorial estimates
+
==Detailed factorial estimates==
Direct costs
+
===Direct costs===
 
To make a more accurate estimate, the cost factors that are compounded into the “Lang factor” are considered individually. The direct-cost items that are incurred in the construction of a plant, in addition to the cost of equipment are:
 
To make a more accurate estimate, the cost factors that are compounded into the “Lang factor” are considered individually. The direct-cost items that are incurred in the construction of a plant, in addition to the cost of equipment are:
  
Equipment erection, including foundations and minor structural work.
+
*Equipment erection, including foundations and minor structural work.
Piping, including insulation and painting.
+
*Piping, including insulation and painting.
Electrical, power and lighting.
+
*Electrical, power and lighting.
Instruments, local and control room.
+
*Instruments, local and control room.
Process buildings and structures.
+
*Process buildings and structures.
Ancillary buildings, offices, laboratory buildings, workshops.
+
*Ancillary buildings, offices, laboratory buildings, workshops.
Storages, raw materials and finished product.
+
*Storages, raw materials and finished product.
Utilities (Services), provision of plant for steam, water, air, firefighting services (if not costed separately).
+
*Utilities (Services), provision of plant for steam, water, air, firefighting services (if not costed separately).
Site, and site preparation.
+
*Site, and site preparation.
 
The contribution of each of these items to the total capital cost is calculated by multiplying the total purchased equipment by an appropriate factor. As with the basic “Lang factor”, these factors are best derived from historical cost data for similar processes. Typical values for the factors are given in several references, Happle and Jordan (1975) and Garrett (1989). Guthrie (1974), splits the costs into the material and labour portions and gives separate factors for each. In a booklet published by the Institution of Chemical Engineers, IChemE (1988), the factors are shown as a function of plant size and complexity.
 
The contribution of each of these items to the total capital cost is calculated by multiplying the total purchased equipment by an appropriate factor. As with the basic “Lang factor”, these factors are best derived from historical cost data for similar processes. Typical values for the factors are given in several references, Happle and Jordan (1975) and Garrett (1989). Guthrie (1974), splits the costs into the material and labour portions and gives separate factors for each. In a booklet published by the Institution of Chemical Engineers, IChemE (1988), the factors are shown as a function of plant size and complexity.
  
Line 184: Line 180:
 
In addition to the direct cost of the purchase and installation of equipment, the capital cost of a project will include the indirect costs listed below. These can be estimated as a function of the direct costs.
 
In addition to the direct cost of the purchase and installation of equipment, the capital cost of a project will include the indirect costs listed below. These can be estimated as a function of the direct costs.
  
Indirect costs
+
== Indirect costs==
 
Design and engineering costs, which cover the cost of design and the cost of “engineering” the plant: purchasing, procurement and construction supervision. Typically 20 per cent to 30 per cent of the direct capital costs.
 
Design and engineering costs, which cover the cost of design and the cost of “engineering” the plant: purchasing, procurement and construction supervision. Typically 20 per cent to 30 per cent of the direct capital costs.
 
Contractor’s fees, if a contractor is employed his fees (profit) would be added to the total capital cost and would range from 5 per cent to 10 per cent of the direct costs.
 
Contractor’s fees, if a contractor is employed his fees (profit) would be added to the total capital cost and would range from 5 per cent to 10 per cent of the direct costs.
 
Contingency allowance, this is an allowance built into the capital cost estimate to cover for unforeseen circumstances (labour disputes, design errors, adverse weather). Typically 5 per cent to 10 per cent of the direct costs.
 
Contingency allowance, this is an allowance built into the capital cost estimate to cover for unforeseen circumstances (labour disputes, design errors, adverse weather). Typically 5 per cent to 10 per cent of the direct costs.
Operating Costs
+
==Operating Costs==
 
An estimate of the operating costs, the cost of producing the product, is needed to judge the viability of a project, and to make choices between possible alternative processing schemes. These costs can be estimated from the flow-sheet, which gives the raw material and service requirements, and the capital cost estimate.
 
An estimate of the operating costs, the cost of producing the product, is needed to judge the viability of a project, and to make choices between possible alternative processing schemes. These costs can be estimated from the flow-sheet, which gives the raw material and service requirements, and the capital cost estimate.
  
 
The cost of producing a chemical product will include the items listed below. They are divided into two groups.
 
The cost of producing a chemical product will include the items listed below. They are divided into two groups.
  
Fixed operating costs: costs that do not vary with production rate. These are the bills that have to be paid whatever the quantity produced.
+
*Fixed operating costs: costs that do not vary with production rate. These are the bills that have to be paid whatever the quantity produced.
Variable operating costs: costs that are dependent on the amount of product produced.
+
*Variable operating costs: costs that are dependent on the amount of product produced.
Fixed costs
+
===Fixed costs===
Maintenance (labour and materials).
+
*Maintenance (labour and materials).
Operating labour.
+
*Operating labour.
Laboratory costs.
+
*Laboratory costs.
Supervision.
+
*Supervision.
Plant overheads.
+
*Plant overheads.
Capital charges.
+
*Capital charges.
Rates (and any other local taxes).
+
*Rates (and any other local taxes).
Insurance.
+
*Insurance.
Licence fees and royalty payments.
+
*Licence fees and royalty payments.
Variable costs
+
===Variable costs===
Raw materials.
+
*Raw materials.
Miscellaneous operating materials.
+
*Miscellaneous operating materials.
Utilities (Services).
+
*Utilities (Services).
Shipping and packaging.
+
*Shipping and packaging.
 
The division into fixed and variable costs is somewhat arbitrary. Certain items can be classified without question, but the classification of other items will depend on the accounting practice of the particular organisation.
 
The division into fixed and variable costs is somewhat arbitrary. Certain items can be classified without question, but the classification of other items will depend on the accounting practice of the particular organisation.
  
Line 216: Line 212:
 
The costs listed above are the direct costs of producing the product at the plant site. In addition to these costs the site will have to carry its share of the Company’s general operating expenses. These will include:
 
The costs listed above are the direct costs of producing the product at the plant site. In addition to these costs the site will have to carry its share of the Company’s general operating expenses. These will include:
  
General overheads.
+
*General overheads.
Research and development costs.
+
*Research and development costs.
Sales expense.
+
*Sales expenses.
Reserves.
+
*Reserves.
How these costs are apportioned will depend on the Company’s accounting methods. They would add about 20 to 30 per cent to direct production costs at the site.
+
*How these costs are apportioned will depend on the Company’s accounting methods. They would add about 20 to 30 per cent to direct production costs at the site.
  
References
+
= References =
Gavin Towler, R. K. Sinnott: Chemical Engineering Design 2nd Edition, https://www.elsevier.com/books/chemical-engineering-design/towler/978-0-08-096659-5
+
- Gavin Towler, R. K. Sinnott: Chemical Engineering Design 2nd Edition, https://www.elsevier.com/books/chemical-engineering-design/towler/978-0-08-096659-5
Pintelon, L. & Puyvelde, F. V., 1997. Estimating Plant Construction Costs. Chemical Engineering, August, pp. 98-104
+
- Pintelon, L. & Puyvelde, F. V., 1997. Estimating Plant Construction Costs. Chemical Engineering, August, pp. 98-104
Humphreys, K. K., 2005. Project and Cost Engineers' Handbook. 4th ed. s.l.:Marcel Dekker
+
- Humphreys, K. K., 2005. Project and Cost Engineers' Handbook. 4th ed. s.l.:Marcel Dekker
Peters, M., Timmerhaus, K. & West, R., 2004. Plant Design and Economics for Chemical Engineers. 5th ed. s.l.:McGraw-Hill
+
- Peters, M., Timmerhaus, K. & West, R., 2004. Plant Design and Economics for Chemical Engineers. 5th ed. s.l.:McGraw-Hill
Vatavuk, W. M., 2002. Updating the CE Plant Cost Index. Chemical Engineering, January, pp. 62-70
+
- Vatavuk, W. M., 2002. Updating the CE Plant Cost Index. Chemical Engineering, January, pp. 62-70
Couper, J. R., 2003. Process Engineering Economics. s.l.:Marcel Dekker
+
- Couper, J. R., 2003. Process Engineering Economics. s.l.:Marcel Dekker
Albright, L.. 2008. Albright's Chemical Engineering Handbook. s.l.:CRC-Press
+
- Albright, L.. 2008. Albright's Chemical Engineering Handbook. s.l.:CRC-Press
http://www.chemengonline.com/pci/
+
- http://www.chemengonline.com/pci/
http://www.equipment-cost-index.com/
+
- http://www.equipment-cost-index.com/
http://www.intratec.us/ic
+
- http://www.intratec.us/ic

Revision as of 17:48, 26 June 2019

About

Capital Cost Estimator is a software which estimates Capital and Operating Costs for a Chemical Processing Plant based on data from the currently active flowsheet.

WARNING

This software should be used for educational purposes only!

The data and information within the software has been obtained from a wide variety of literature sources. While reasonable care has been exercised in the collection of data and testing of this software, the author of the software disclaims any warranty, expressed or implied, as to the accuracy or reliability of the data or calculations contained therein. The results of calculations obtained from the software yield approximate results, which will not always be suitable for every application. The software is designed for use by trained professional personnel and is not a substitute for sound professional judgment. It is the sole responsibility of the user to validate the data presented by the software and to determine whether the results of this program are accurate and suitable for any specific purpose. No guarantee of accuracy or fitness for any purpose is expressed or implied. The author strongly recommends that the data be checked against other sources and/or methods before use and application. The author shall not be held liable for any direct, indirect, consequential or incidental damages incurred through use of the data or calculations.

Features

  • Capital Cost Estimation
  • Yearly Operating Cost Estimation
  • Saving/Loading of Cost Reports
  • Compare multiple Cost Reports
  • Import Data from DWSIM Simulation Files, COCO/COFE Flowsheet files and DESIGN II Excel Reports (standalone version only)
  • Export results to DOC/ODT/XLS/ODS/PDF files
  • Automatic mapping for selected equipments, product/raw streams and utilities
  • Price correction based on CEPCI and IPC Cost Indexes
  • Currency conversion

System Requirements

Supported Operating Systems: Windows/Linux [DWSIM Plugin Version] Minimum required DWSIM version: 4.3 with Update 6 [Standalone Application Version] Minimum required Framework version: .NET 4.5/Mono 4.0

Download

Plugin for DWSIM Simulator

The Capital Cost Estimator Plugin for DWSIM Simulator is available to purchase for USD 25. The software license is non-transferrable, that is, after downloading the plugin, you cannot redistribute it to anyone.

A lot of effort was put on making this software, in the hope that it will be useful. You can support future developments simply by doing things the right way: please do not give this plugin for free to anyone, and encourage your colleagues to download it through the official channel.

Click here to go to the download/purchase page: Capital Cost Estimator (DWSIM Plugin Version) Download Page

Standalone Application

The Capital Cost Estimator (Standalone App Version) is available to purchase for USD 29. The software license is non-transferrable, that is, after downloading the package, you cannot redistribute it to anyone.

Click here to go to the download/purchase page: Capital Cost Estimator (Standalone App Version) Download Page

Installation

DWSIM Plugin Version

Unzip the downloaded package. Copy the DWSIM.CapitalCostEstimator.dll and DWSIM.CapitalCostEstimator.pdb files to the "plugins" folder inside DWSIM's current installation directory.

Running the plugin

Start DWSIM and open/create a flowsheet. Go to the "Plugins" menu, you should see a new item called "Capital Cost Estimator". Click on it and the plugin interface will be shown on the screen.

Existing Unit Operations and Material/Energy Streams will be mapped to Equipments, Materials and Utilities, whose parameters can be freely modified.

Standalone Application Version

Unzip the downloaded package and run the executable file.

General Usage Instructions

New/Load/Save

To create a new Cost Report, click on the "New Report" menu button. To load an existing report, click on the "Load Report" menu button. To save the currently selected report, click on the "Save Report" menu button.

Compare Reports

To compare the currently opened reports, click on the "Compare Reports" menu button.

Report Setup

On this tab you will enter basic report information like name, description, reference date, cost index selection and currency details. The currency converter is based on a webservice, which depends on an active internet connection to work.

Ccostplugin1.png

Equipment Mapping

Some equipments are automatically mapped from Unit Operations, though you can modify the calculated values and change the selected equipments at any time. The correction factors are multiplied by the current prices to form the final total equipment cost.

Ccostplugin2.png

Material Stream Mapping

Material Streams can be mapped to Raw Materials and/or Products, which will be used to calculate Yearly Operating Costs.

Ccostplugin4.png

Utility Mapping

You can map Material and Energy Streams to some predefined Process Utilities, and the plugin will automatically calculate the cost based on the mass or energy flow, depending on the stream type.

Ccostplugin5.png

Capital Cost Summary

Here you'll see a summary of the items that make up the Total Capital Cost. You can change the calculation basis (Percentage or Absolute value) for most items, except for those who are calculated based on the previously mapped items.

Ccostplugin6.png

Yearly Operating Cost Summary

Here you'll see a summary of the items that make up the Total Yearly Operating Cost. You can change the calculation basis (Percentage or Absolute value) for most items, except for those who are calculated based on the previously mapped items.

Ccostplugin7.png

Export Results

From this tab you can export the calculated results to a document file (DOC, ODT, PDF) or a spreadsheet file (XLS, ODS).

Ccostplugin8.png

Cost Estimation Basis

Most of the calculation methods on this plugin are based on the Factorial Method described on the Chemical Engineering Design book by R. K. Sinott [1], which you should refer to for more information.

Introduction

Cost estimation is a specialised subject and a profession in its own right. The design engineer, however, needs to be able to make quick, rough, cost estimates to decide between alternative designs and for project evaluation. Chemical plants are built to make a profit, and an estimate of the investment required and the cost of production are needed before the profitability of a project can be assessed.

Accuracy and Purpose of Capital Cost Estimates

The accuracy of an estimate depends on the amount of design detail available: the accuracy of the cost data available; and the time spent on preparing the estimate. In the early stages of a project only an approximate estimate will be required, and justified, by the amount of information by then developed.

Capital cost estimates can be broadly classified into three types according to their accuracy and purpose:

  • Preliminary (approximate) estimates, accuracy typically 30 per cent, which are used in initial feasibility studies and to make coarse choices between design alternatives. They are based on limited cost data and design detail.
  • Authorisation (Budgeting) estimates, accuracy typically 10 15 per cent. These are used for the authorisation of funds to proceed with the design to the point where an accurate and more detailed estimate can be made. Authorisation may also include funds to cover cancellation charges on any long delivery equipment ordered at this stage of the design to avoid delay in the project. In a contracting organisation this type of estimate could be used with a large contingency factor to obtain a price for tendering. Normally, however, an accuracy of about š5 per cent would be needed and a more detailed estimate would be made, if time permitted. With experience, and where a company has cost data available from similar projects, estimates of acceptable accuracy can be made at the flow-sheet stage of the project. A rough P&I diagram and the approximate sizes of the major items of equipment would also be needed.
  • Detailed (Quotation) estimates, accuracy 5-10 per cent, which are used for project cost control and estimates for fixed price contracts. These are based on the completed (or near complete) process design, firm quotations for equipment, and a detailed breakdown and estimation of the construction cost.

The cost of preparing an estimate increases from about 0.1 per cent of the total project cost for 30 per cent accuracy, to about 2 per cent for a detailed estimate with an accuracy of š5 per cent.

Cost Escalation (Inflation)

The cost of materials and labour has been subject to inflation since Elizabethan times. All cost-estimating methods use historical data, and are themselves forecasts of future costs. Some method has to be used to update old cost data for use in estimating at the design stage, and to forecast the future construction cost of the plant.

The method usually used to update historical cost data makes use of published cost indices. These relate present costs to past costs, and are based on data for labour, material and energy costs published in government statistical digests.

Chemical plant cost indexes are dimensionless numbers employed to updating capital cost required to erect a chemical plant from a past date to a later time, following changes in the value of money due to inflation and deflation. Since, at any given time, the number of chemical plants is insufficient to use in a preliminary or predesign estimate, cost indexes are handy for a series of management purposes, like long-range planning, budgeting and escalating or de-escalating contract costs.[2]

A cost index is the ratio of the actual price in a time period compared to that in a selected base period (a defined point in time or the average price in a certain year), multiplied by 100. Raw materials, products and energy prices, labor and construction costs change at different rates, and plant construction cost indexes are actually a composite, able to compare generic chemical plants capital costs.

Calculation methods

Although the available indexes are compiled in several ways, they are defined to encompass a specific set of conditions and items. Prices for these items can be obtained either through company’s purchasing department data or through published indexes, like those published by the Bureau of Labor Statistics (BLS).[3] Both the CE and the IC indexes, from Chemical Engineering and Intratec, respectively, employs BLS’ data.

The weighting of such factors, which is defined by the realized degree of importance of each component in the specific index (or sub-index), aims to represent the costs variations typically found for chemical plants.

Using a cost index

To update an item cost (equipment, projects) from period A to period B, is necessary to multiply period A’s cost by the ratio of period B’s index over period A’s index, according to the following equation:

[math]\text{Cost at B} = \text{Cost at A}\cdot \frac{\text{index at B }}{\text{index at A }}[/math]

As a rule-of-thumb, cost indexes permit fairly accurate estimates for cost escalation if the difference between period A and period B is less than 10 years. Differences between the actual equipment and labor prices and those predicted by the index tend to grow over the years, surpassing the typical error verified in budget-level estimates.[4][5]

Cost Indexes in Engineering

The selection of the proper index to use depends on the industry in which it is applied. For example, while CE, M&S or IC Index are typically employed for chemical process industries, the ENR (Engineering News-Record) construction index is used for general industrial construction and takes in account the prices for fixed amounts of structural steel, cement, lumber and labor.

The majority of cost indexes demonstrate a time lag, due to data collection and its compilation for publishing. As stated before, some indexes use information published by other organizations and a delay in data may be verified (like those provide by the BLS). Exceptions to this are the ENR construction and the IC indexes, which present relatively current values.

The main indexes available for process industries include:

  • Chemical Engineering Index, CEPCI: composed of 4 major components – equipment, construction labor, buildings, and engineering and supervision – the index is employed primary as a process plant construction index, was established using a base period of 1957-1959 as 100. The CE Index is updated monthly and it lags in time by about 3 months. The CE Index was revised in 1982, to account for changes in labor productivity and, again, in 2002.[6] Published in each issue of Chemical Engineering.[7][8]
  • Marshall and Swift Cost Index, M&S (originally known as Marshall and Stevens Index): a composite of two major components - process-industry equipment average and all-industry equipment average - was established in 1926 with a value of 100. Some industries considered in the process-industry equipment average are chemicals, petroleum products, rubber and paper. The all-industry average encompasses 47 different types of industrial, commercial and housing equipment. Published monthly in each issue of Chemical Engineering until April 2012.[9]

Intratec Chemical Plant Construction Index, IPC: a process plant construction index developed by Intratec, a chemical consulting company. Although cost indexes do not usually forecast future escalation, the IC Index stands out for presenting a smaller delay between release date and index date, besides a 12 months forecast. On the other hand, the index is only available from January 2000 (with a value of 100). A sample is available at Intratec’s website.[10]

  • Nelson-Farrar Indexes, NF (originally known as the Nelson Refinery Construction Indexes): established in 1946 with a value of 100, the index is more suitable for petroleum or petrochemical business. Published once a month in the Oil and Gas Journal.

Location Factor In order to be able to use the available standard indexes to locations where index data is not available we have to incorporate a new term called the Location Factor (LF) to the standard index value. It is a dimensionless value for a particular location relative to either of the above-mentioned basis:

[math]\text{Cost in A} = \text{Cost in USGC} \cdot \text{LF(A)}[/math]

where A is the location for which cost is being evaluated and LF(A) is the location factor for the location A relative to USGC.

Location factors are greatly influenced by currency exchange rates due to their significant effect on Index value and hence vary drastically with time. Over the past couple of decades the location factors for various locations are trending close to the value 1. However location factor for a particular region within a country can be easily determined by adding 10% to the index of the reference location for every 1000 miles. The reference location is usually a major industrial location closest to the location where the index is being determined. Location factors for various locations have been published and updated in various journals as in Aspen Richardson's "International Construction Cost Factor Location Manual (2003)".

The Factorial Method for Capital Cost Estimation

Capital cost estimates for chemical process plants are often based on an estimate of the purchase cost of the major equipment items required for the process, the other costs being estimated as factors of the equipment cost. The accuracy of this type of estimate will depend on what stage the design has reached at the time the estimate is made, and on the reliability of the data available on equipment costs. In the later stages of the project design, when detailed equipment specifications are available and firm quotations have been obtained, an accurate estimation of the capital cost of the project can be made.

Lang factors

The factorial method of cost estimation is often attributed to Lang (1948). The fixed capital cost of the project is given as a function of the total purchase equipment cost by the equation:

[math]Cf_D = f_L \cdot C_e[/math]

where [math]Cf_D[/math] is fixed capital cost, [math]C_e[/math] is the total delivered cost of all the major equipment items: storage tanks, reaction vessels, columns, heat exchangers, etc. and [math]f_L[/math] is the Lang factor, which depends on the type of process.

The values given above should be used as a guide; the factor is best derived from an organisation’s own cost files.

The above equation can be used to make a quick estimate of capital cost in the early stages of project design, when the preliminary flow-sheets have been drawn up and the main items of equipment roughly sized.

Detailed factorial estimates

Direct costs

To make a more accurate estimate, the cost factors that are compounded into the “Lang factor” are considered individually. The direct-cost items that are incurred in the construction of a plant, in addition to the cost of equipment are:

  • Equipment erection, including foundations and minor structural work.
  • Piping, including insulation and painting.
  • Electrical, power and lighting.
  • Instruments, local and control room.
  • Process buildings and structures.
  • Ancillary buildings, offices, laboratory buildings, workshops.
  • Storages, raw materials and finished product.
  • Utilities (Services), provision of plant for steam, water, air, firefighting services (if not costed separately).
  • Site, and site preparation.

The contribution of each of these items to the total capital cost is calculated by multiplying the total purchased equipment by an appropriate factor. As with the basic “Lang factor”, these factors are best derived from historical cost data for similar processes. Typical values for the factors are given in several references, Happle and Jordan (1975) and Garrett (1989). Guthrie (1974), splits the costs into the material and labour portions and gives separate factors for each. In a booklet published by the Institution of Chemical Engineers, IChemE (1988), the factors are shown as a function of plant size and complexity.

The accuracy and reliability of an estimate can be improved by dividing the process into sub-units and using factors that depend on the function of the sub-units; see Guthrie (1969). In Guthrie’s detailed method of cost estimation the installation, piping and instrumentation costs for each piece of equipment are costed separately. Detailed costing is only justified if the cost data available are reliable and the design has been taken to the point where all the cost items can be identified and included.

In addition to the direct cost of the purchase and installation of equipment, the capital cost of a project will include the indirect costs listed below. These can be estimated as a function of the direct costs.

Indirect costs

Design and engineering costs, which cover the cost of design and the cost of “engineering” the plant: purchasing, procurement and construction supervision. Typically 20 per cent to 30 per cent of the direct capital costs. Contractor’s fees, if a contractor is employed his fees (profit) would be added to the total capital cost and would range from 5 per cent to 10 per cent of the direct costs. Contingency allowance, this is an allowance built into the capital cost estimate to cover for unforeseen circumstances (labour disputes, design errors, adverse weather). Typically 5 per cent to 10 per cent of the direct costs.

Operating Costs

An estimate of the operating costs, the cost of producing the product, is needed to judge the viability of a project, and to make choices between possible alternative processing schemes. These costs can be estimated from the flow-sheet, which gives the raw material and service requirements, and the capital cost estimate.

The cost of producing a chemical product will include the items listed below. They are divided into two groups.

  • Fixed operating costs: costs that do not vary with production rate. These are the bills that have to be paid whatever the quantity produced.
  • Variable operating costs: costs that are dependent on the amount of product produced.

Fixed costs

  • Maintenance (labour and materials).
  • Operating labour.
  • Laboratory costs.
  • Supervision.
  • Plant overheads.
  • Capital charges.
  • Rates (and any other local taxes).
  • Insurance.
  • Licence fees and royalty payments.

Variable costs

  • Raw materials.
  • Miscellaneous operating materials.
  • Utilities (Services).
  • Shipping and packaging.

The division into fixed and variable costs is somewhat arbitrary. Certain items can be classified without question, but the classification of other items will depend on the accounting practice of the particular organisation.

The items may also be classified differently in cost sheets and cost standards prepared to monitor the performance of the operating plant. For this purpose the fixed-cost items should be those over which the plant supervision has no control, and the variable items those for which they can be held accountable.

The costs listed above are the direct costs of producing the product at the plant site. In addition to these costs the site will have to carry its share of the Company’s general operating expenses. These will include:

  • General overheads.
  • Research and development costs.
  • Sales expenses.
  • Reserves.
  • How these costs are apportioned will depend on the Company’s accounting methods. They would add about 20 to 30 per cent to direct production costs at the site.

References

- Gavin Towler, R. K. Sinnott: Chemical Engineering Design 2nd Edition, https://www.elsevier.com/books/chemical-engineering-design/towler/978-0-08-096659-5 - Pintelon, L. & Puyvelde, F. V., 1997. Estimating Plant Construction Costs. Chemical Engineering, August, pp. 98-104 - Humphreys, K. K., 2005. Project and Cost Engineers' Handbook. 4th ed. s.l.:Marcel Dekker - Peters, M., Timmerhaus, K. & West, R., 2004. Plant Design and Economics for Chemical Engineers. 5th ed. s.l.:McGraw-Hill - Vatavuk, W. M., 2002. Updating the CE Plant Cost Index. Chemical Engineering, January, pp. 62-70 - Couper, J. R., 2003. Process Engineering Economics. s.l.:Marcel Dekker - Albright, L.. 2008. Albright's Chemical Engineering Handbook. s.l.:CRC-Press - http://www.chemengonline.com/pci/ - http://www.equipment-cost-index.com/ - http://www.intratec.us/ic